Industrial · Procurement

How to Write an RFQ for Industrial Surface Preparation

How buyers write comparable surface-preparation RFQs for Alberta plant and project work.

Read on ↓

Evolve Eco Blasting  ·  Edmonton & Alberta  ·  Published November 5, 2026  ·  12 min read

The short version An industrial surface-preparation RFQ works when it defines the outcome the coating needs: cleanliness, profile, access, waste, hold points, and acceptance records. State the substrate and existing condition, name the SSPC or ISO cleanliness grade by full designation, require an anchor-profile range from the coating data sheet, and include vendor qualification, silica controls, containment, and documentation in the bid package. Vague method-only language leaves room for unequal bids and weak preparation.

A useful abrasive-blasting quote is only as clear as the package it answers. When a request says little more than "sandblast structural steel and recoat," bidders fill the gaps differently on scope, standard, and risk. The lowest number can win for the wrong reasons, and the coating system pays for the difference later. This guide is for buyers, plant engineers, turnaround planners, and project managers who need comparable bids for larger industrial surface-preparation work across Edmonton and greater Alberta.

It is not a substitute for a coating specification or an engineering standard. It is the practical checklist that turns those documents into a bid package vendors can price, inspectors can verify, and your team can defend when the coating has to last.

Why RFQs, not phone quotes, matter on industrial work

Small residential or one-off commercial jobs can start with photos and a site visit. Larger industrial work sits inside shutdown calendars, contractor-management systems, coating warranties, and OH&S expectations. The RFQ is where those constraints become visible to bidders at the same time.

A clear RFQ does three things at once. It forces the owner's team to decide what "done" means before mobilisation. It lets vendors price the same deliverable instead of competing on unspoken assumptions. And it creates the paper trail that later supports warranty, audit, and change-order decisions. Vague language invites change orders, schedule fights, and preparation that looks clean but fails the coating data sheet.

Evolve Eco Blasting answers industrial RFQs as a mobile surface-preparation contractor. We do not write your coating specification for you. We do need that specification, or a clear interim standard, before a bid is meaningful. The same discipline appears in our guide to how to prepare metal for coating and in the shutdown sequence described for industrial and water tank cleaning and restoration.

Start with the asset, not the method

Open the RFQ with what is being prepared, not with "dustless blasting" or "sandblasting." Method follows constraint. Substrate and service decide the standard.

Include, at minimum:

If you do not know the existing coating chemistry, say so and require a site assessment or sampling before final pricing. Hidden lead, chrome, or other regulated coatings change containment and disposal. Leaving that unknown in the RFQ usually moves the cost into a disputed change order later.

Name the SSPC or ISO cleanliness standard by full designation

"Near-white blast" is a conversation. "SSPC-SP 10 / NACE No. 2 Near-White Metal Blast Cleaning" is a specification. Joint SSPC/NACE standards (now stewarded under AMPP) define visual cleanliness for blast cleaning. Commercial blast cleaning (SSPC-SP 6 / NACE No. 3) allows staining on up to about one third of each unit area. Near-white (SSPC-SP 10 / NACE No. 2) tightens that allowance to no more than about five percent. White metal (SSPC-SP 5 / NACE No. 1) permits no staining. Those allowances are why two bids that both say "blast clean" can describe completely different effort. (SSPC-SP 10 / NACE No. 2 preview; SSPC-SP 6 / NACE No. 3 preview)

Write the full designation for each zone if requirements differ. Primary structure might be SP 10 while a secondary gallery is SP 6. Spot repairs inaccessible to blast equipment may need an SP 11 power-tool clause. Do not leave zone interpretation to the field. Where ISO 8501-1 grades appear in owner standards, state them explicitly and note that ISO and SSPC/NACE grades are related but not always treated as exact equivalents in inspection practice.

The cleanliness grade still does not define anchor profile. Profile comes from the coating manufacturer's data sheet and must be written separately.

Require profile, contamination limits, and the flash-rust window

Treat cleanliness, profile, and surface chemistry as separate acceptance criteria.

State:

Your coating system and owner standard decide which of these apply on a given package. A preparation contractor's job is to meet the written acceptance criteria in the package and document what was achieved.

Put inspection hold points in the bid, not in a later email

If primer can go down before anyone verifies the blast, acceptance has already slipped out of the package. Hold points are how you keep verification in the sequence.

At minimum, require:

SSPC-PA 2 and related coating-inspection practices govern dry-film thickness after coating. They do not replace a preparation hold point. Separate the blast acceptance from the paint acceptance so neither trade hides inside the other's paperwork.

Ask for method, media, and silica controls in plain language

Alberta's Occupational Health and Safety framework expects employers conducting abrasive blasting to substitute crystalline silica with a less harmful abrasive where reasonably practicable, and to control release, restricted areas, and decontamination when silica hazards remain (Alberta OHS Code Part 4, s.39; Silica at the work site). CCOHS guidance on abrasive blasting likewise emphasises planning, safer media where possible, preferably water-delivered media to reduce dust, enclosure or barriers, restricted access, and cleanup that does not re-entrain dust (CCOHS: Abrasive Blasting).

Your RFQ should ask bidders to state:

Evaluate every bidder against the same control questions. Your site still needs its own hazard assessment. For method trade-offs, see dustless blasting versus sandblasting and our blasting media guide. Evolve's industrial work uses silica-free media options and a low-dust mobile process where they fit the package; that does not replace the controls your RFQ should require from any contractor.

Vendor qualification questions that belong in the RFQ

Procurement language should separate technical capability from administrative readiness. Ask for evidence, not slogans.

Useful qualification items include:

Do not ask vendors for production rates or lump-sum prices against undefined square metres of unknown coating. Ask them to price defined zones, unit rates with stated assumptions, or a staged price after a paid assessment when condition is uncertain.

Scope tables beat paragraphs

Procurement packages that win clean bids usually include a simple scope table. Columns can be as plain as: zone / substrate / existing condition / cleanliness standard / profile / coating system reference / access / containment class / waste responsibility / hold point / notes.

Attach drawings with hatch for blast limits. State whether bolt holes, backside of members, under cut-outs, and skirt interiors are in or out. State who supplies scaffolding, who isolates energy, who gas-tests confined spaces, and who owns the coating application after preparation. Industrial surface preparation is a trade interface. The RFQ should name the interfaces so the price is not a silent bet on someone else's delay.

What buyers usually need clarified before award

When plant and project teams research surface-prep contractors, the same gaps tend to block a fair shortlist: the cleanliness grade and profile for each zone, who owns the pre-prime hold point, how silica and waste are controlled, and what insurance and platform paperwork is current for the gate. Write those answers into the RFQ so comparable bids answer the same questions. More on industrial mobilisation and documentation is on our industrial capability page.

Frequently asked questions

What is the most important line in a surface-prep RFQ?

The full cleanliness designation tied to a drawing zone, plus the profile range from the coating data sheet. Without both, bidders are not pricing the same surface.

Can I specify the blasting method instead of the result?

You can constrain method for safety or site rules, but acceptance should still be a result: cleanliness, profile, contamination limits, and records. Method-only RFQs hide failures until coating inspection.

Do I need soluble-salt testing on every industrial blasting job?

No. Immersion, marine, and many aggressive industrial services often do. Mild atmospheric work may not. Follow the coating data sheet and owner standard rather than copying another project's number.

How detailed should waste and containment language be in the RFQ?

Detailed enough that two bidders assume the same enclosure, collection, and disposal responsibility. CCOHS expects planning for media hazards, affected people, barriers or enclosure, and cleanup that does not spread contamination. Your site rules add the rest.

Will Evolve help tighten an incomplete industrial RFQ?

Yes, as part of bid clarification. Send what you have. We will flag missing standards, access assumptions, and hold points before anyone mistakes a rough number for a committed price.

Planning a surface-preparation RFQ

Send the coating specification, drawings, access notes, and schedule window. We will tell you plainly what belongs in the bid package and what still needs definition before anyone can price the work fairly.

Planning a tank or vessel project

Silica-free, documented surface preparation to your coating specification, built around your shutdown schedule. Call to discuss scope.